Email me when a new MSHA incident is filed at Coronet Jewell Prep Plant #2.
| Quarter | Hours worked | Citations | S&S | Per 1M hrs |
|---|---|---|---|---|
| 2025 Q4 | 5,883 | 1 | 0 | 170.0 |
| 2025 Q3 | 5,649 | 3 | 1 | 531.1 |
| 2025 Q2 | 7,333 | 0 | 0 | 0.0 |
| 2025 Q1 | 6,899 | 6 | 1 | 869.7 |
| 2024 Q3 | 7,800 | 0 | 0 | 0.0 |
| 2024 Q2 | 0 | 0 | 0 | |
| 2024 Q1 | 0 | 5 | 1 | |
| 2023 Q4 | 0 | 0 | 0 |
Coming down little grade. EE had truck in higher gear. Got brakes hot and couldn't make turn. Truck over turned.
Reported on August 5th that an employee had filed a compensable hearing loss claim.
EE was cleaning the shop and was attempting to drag a piece of fabricated pipe across a steel work table. The pipe pivoted catching the ee's left index finger between the pipe and table.
He was dislodging ice from 2" discharge pump by hitting the hose on a concrete barrier when the ice was loosen the hose was uncontrollable, the of hose hit him in the face.
Using a 1/2" electric drill to drill 1-1/2" holes through plywood using a flat wood boring bit. As he was drilling, the bit bound up in the wood causing the drill's handle to twist, bending his right ring & pinky fingers. (NOTE: Drill was NOT equipped with a trigger lock.) He let go of the trigger as soon as he noticed it bind, but couldn't get his hand away fast enough.
The employee was working on the triple deck to replace a bad screen in the discharger end of the bottom deck. The EE was cutting out the huck bolts in the back plate to remove the screen. The EE stated he cut all the bolts out except two. These 2 bolts were left in until a means of securing the plate was in place. 1 bolt did not have a nut & the plate fell on his foot.
Was pulling oxygen bottle on dollie across floor at tipple.
Employee alleges to have contracted Coal Workers Pneumoconiosis while employeed at Jewell Smokeless Coal Corporation. We were informed on 1/24/07 that the employee had been diagnosed with the illness at Stage 1/0.
I-Beam was lifted and employee was cleaning dirt off of it. The lifting clamp slipped off and I-beam fell, striking employee on foot.
EMPLOYEE WAS PAINTING I-BEAMS FROM MANLIFT AND WAS BITTEN BY A SPIDER.
EMPLOYEE WAS CUTTING AN I-BEAM APART. AS HE WAS CUTTING THE I-BEAM, IT SHIFTED AND FELL ON EMPLOYEE'S FOOT.
THE EMPLOYEE INJURED HIS NECK DURING AN ALTERCATION AT THE HEAVY EQUIPMENT SHOP, LOST HIS BALANCE AND FELL TO THE GROUND.
EMPLOYEE WAS CARRYING SAE2 CLEANER (70-80 LB) FROM TRUCK TO SILO. WALKWAY WAS NARROW. HE TRIPPED ON ROCK/COAL IN GRATE AND FELL ON SAME LEVEL.
AT THE START OF THE SHIFT, THE PREP PLANT WAS STARTED & AN ATTEMPT WAS MADE TO START THE REFUSE BELTS. THE NO.1 REFUSE BELT SHOWED A HIGH AMPERAGE READING WHEN ATTEMPTING TO START IT, SO THE F OREMAN, PLANT ELECTRICIAN & A MECHANIC WENT TO THE NO.1 TAILPIECE & FOUND THAT SOME BOLTS HAD BROKEN OUT OF THE FEEDER FRO THE BELT AND ALLOWED REFUSE FINES TO ACCUMULATE AROUND THE BELT TAIL
BUILT UP REFUSE ON CABLE CALMP ALLOWED EE TO LOSE HIS FOOTING AND FALL APPROX. 10 FEET.