Email me when a new MSHA incident is filed at Martin Marietta - Lawyers Rd. Quarry.
| Quarter | Hours worked | Citations | S&S | Per 1M hrs |
|---|---|---|---|---|
| 2025 Q4 | 12,226 | 0 | 0 | 0.0 |
| 2025 Q3 | 8,713 | 0 | 0 | 0.0 |
| 2025 Q2 | 3,090 | 0 | 0 | 0.0 |
| 2025 Q1 | 7,030 | 0 | 0 | 0.0 |
| 2024 Q4 | 4,988 | 1 | 0 | 200.5 |
| 2024 Q3 | 5,456 | 0 | 0 | 0.0 |
| 2024 Q1 | 3,817 | 0 | 0 | 0.0 |
| 2023 Q4 | 4,989 | 0 | 0 | 0.0 |
Employee was holding a bolt with a pair of locking pliers. Another employee was using a reciprocating saw to cut the bolt. When the bolt was but through, the saw sung up and cut the employee's finger.
Senior Employee who wears a pacemaker experienced shortness of breath and felt heartbeat was abnormal
Employee was cutting an information from a hydraulic hose with carpet knife, knife slipped and cut thumb on left hand.
Miner was walking down the rock ramp that had been dug out at the surge pile to reach the feeder. The miner was part of a crew working on the surge pile feeder. It had been raining all morning and the rock was wet. The employee slipped and cut a finger on the rock as they caught themselves.
Driller had placed a cardboard blast hole tube into a completed hole, while cutting to proper height of tube above the ground. EE was pulling EE's cut off tool toward self, tool slipped sticking in EE's right lower leg.
Injured EE was connecting lifting strap from Bearing to Crane Hook. Bearing was propped to provide access to opening for strap connection. Bearing shifted from raised position and EE was suddenly supporting most of the weight.
Helping load a shot, sitting in the truck operating the controls, started to feel nauseous. (Diagnosed with vertigo)
EE was driving a Terex 3066 C Articulated Rear Dump Truck down a steep gravel haul road into a turn. The equipment's rear tandem tires began to "buck jump". EE applied brakes. Truck slid sideways and turned over on right side. EE caught arm in steering wheel and broke right humerus.
Employee was using a pole to clean out the pug-mill hopper. When the employee thrust the pole into the material, he hit the outside edge of his right hand on the corner of a drive belt guard. This caused a cut in the hand and 7 stitches were required.
Employee was chipping a recent weld when some hot slag was chipped onto his left elbow. The employee waited two weeks to seek medical attention when the elbow became red and swollen. He did not indicate injury was definitely he related until 10/09/06 ( the return to work date).
The employee was dipping the sediment pond using the track hoe. Some of the mud fell out of the bucket, hit the handrail on the track hoe, ricocheted through the open window and hit the employee in the corner of his left eye. The employee was wearing safety glasses.
JOB DETAIL: REMOVE PLATFORM SURROUNDING A STONE CRUSHER. JOB PLAN: CUT THE 16'X28' PLATFORM IN HALF, RIG , AND REMOVE EACH SECTION. ACCIDENT: UNKNOWN TO THE EE, THE PLATE WAS NOT ATTACHED TO T HE SUPPORT STEEL. HE WAS IN THE CENTER OF PLATFORM WHEN HE CUT THE PLATE TO 27"X96", THE PLATE FELL 11'3" TO THE GROUND WITH THE EE LANDING ON TOP.
THE EE WAS WALKING FROM HIS TRUCK TO THE BREAK ROOM WHEN HE SLIPPED ON SOME ICE.
EE WAS COMING OUT OF DOORS USED AS A LOADING DOCK-HE STEPPED ON A PALLET, 2 OF THE BOARDS BROKE, TWISTING HIS ANKLE.
EE WAS PUSHING ON A GATE HANLE ON A VIBRATING SCREEN WHEN HE FELT A PAIN IN HIS LOWER TO MID BACK.
EE WAS HAMMERING IN A WEDGE WITH AN 8 LB. HAMMER WHEN HE ACCIDENTALLY HIT THE MIDDLE FINGER ON HIS LEFT HAND. EE WAS WEARING GLOVES.
EMPLOYEE WAS CARRYING SCREEN CLOTH UP STEPS WHENHE FELT PAIN IN HIS LOWER LEFTHAND SIDE OF BACK.EMPLOYEE WENT TO DOCTOR ON 5/25/2000.