Young Mill Metal/Non-Metal

Employee was exiting a light duty vehicle when their foot slipped in-between the railing and the truck which resulted in a fracture to the left ankle.

Employee was trying to remove a loader bucket tooth from the 136 conveyor belt. The employee stopped the belt and the tooth was under the belt magnet. When they grabbed the tooth, the magnet pulled their hand up with the tooth and smashed a finger.

Employee states EE was working on the ball mill trying to fix an oil leak. EE went to leave and lost EE's balance and grabbed the handrail, EE then felt burning and sharp pain in EE's left shoulder area.

Employee fell while washing out under a silo with a water hose. When the hose was turned on, the pressure made employee take a step backwards and employee tripped, landing on a step and felt pain in lower back.

An employee smashed their finger while installing rebar with a 4lb hammer. As the employee swung the hammer EE missed the rebar and EE's finger hit the side of the form board.

Technician was removing a cone seal from the engine of 33010 Truck. When the seal broke loose, technician's hand nicked the corner of the block and cut EE's knuckle.

An employee was walking up the set of steps near the MCC room and felt knee pop and felt a burning sensation with swelling

Employee was performing routine maintenance of crusher and when walking down crusher stairs, foot got hung up causing employee to lose balance. In the process of catching self from falling, employee jammed/twisted back.

The injured employee was overseeing a trailer being unloaded. The chain snapped and caught IE's ear. IE was wearing all of their required PPE. The injury was minor and required just a few stitches.

While removing bucket off loader employee struck dog bone pin with pipe, the pin slipped out and the pipe moved, resulting in pinching fingers between pipe and bucket. Employee crushed 3rd and 4th digit finger and distal fracture of ring finger.

Using torch without gloves and melted rubber landed on hand.

kneeling on grate and when he stood up, felt pop in knee

EE set up a hand pump press with one end against the left loader frame and the other end against the right lift cylinder pin. EE had hand pump engaged with pressure on the pin. The pin did not move. EE climbed down off the machine to get a drink and as he walked toward his truck, he heard a pop noise and he turned around to see what the noise was the pin ejected out, hit his head.

Welding, changed position and fell against a rusty piece of metal causing a laceration to rt forearm.

slipped on ladder and fell

Hearing loss. Did not return for 30 day retest. Had a 10 dB avg shift with threshold above 25 dB. Recvd disc from audiologist on 3/21/14

Hearing loss. Did not return for 30 day retest. Had a 10 dB avg shift with threshold above 25 dB. Recvd final disc on 3/21/14

Did not return for 30 day retest. Recvd disc from audiologist with final results on 3/21/2014. Had a 10 dB avg shift with threshold above 25 dB

Stepped off ladder into wet concentrate and rolled his ankle

Dismounting from loader and bottom step broke resulting in a fall injuring his back and knee.

Stepped from loader ladder to platform on fuel tank. Did not maintain 3 point contact and slipped and fell.

Shoveling rock from platform

While bending down injured stated that his knee started hurting, he finished his shift and went to seek medical treatment the next day, diagnosed with strained MCL right knee.

Injured was assisting two co workers place a ladder on the floor for storage. After the ladder was lowered employee stated he felt pain in his back.

EE was walking down a slope on #4 rock when he sprained his right ankle.

EE was replacing belt clips on discharge conveyor, when dried mud fell onto his face. When EE tried to wipe the material off of his face, a small piece fell behind his safety glasses and into his eye. Debris was removed and an antibiotic ointment given.

EE was stepping off of a ladder, when his foot slipped on the edge of a trough in the floor, causing him to fall and strain his left knee.

Employee was working in the lab. He broke a burett containing Nitric Acid. The acid splashed on his chest resulting in minor burns. Employee was treated at a medical facility and released.

Foreman was aligning a densifer - slipped on surface. Reportable due to hairline fx. No restricted duty or lost workdays. Foreman continueing with regular duties. (Blue Ridge Industrial Inc.)

EE TWISTED RIGHT KNEE WHILE CHECKING INSIDE RAIL CARS. THIS HAPPENED WHILE CLIMBING ON LADDER OR STEPPING OFF LADDER TO GROUND. EE NOT SURE EXACTLY WHEN. KNEE HURT AT END OF SHIFT AFTER CHECKI NG/CLEANIN APP 12 CARS.

LOCAL NORFOLK SOUTHERN RAILROAD SWITCHER PUSHING 30 EMPTY CARS COLLIDED WITH STRING OF 6 CARS. EE WAS HIT BY TRACKMOBILE, KNOCKING HIM DOWN OUTSIDE OF THE TRACK AS A RESULT OF THE COLLISION.

EE HAD A POSSIBLE SEIZURE OR FAINTING CONDITION. HE FELL AND HIT HIS HEAD ON CONCRETE SURFACE. HE WAS UNCONSCIOUS MOMENTARILY. THIS CONDITION NOT WORK RELATED. REPORTING STITCHES 2 FOR SMALL L ACERATION TO HEAD.

EE WAS STRUCK IN RIGHT EYE BY ROCK FROM PASSING EQUIPMENT. ROCK DEFLECTED FROM UNDERSIDE OF BRIMOF HARDHAT AND STRUCK EYE. LOST 2 WORKDAYS.

CUT LEFT HAND WHEN INSTALLINT VALVE ON 1" HOSE. STITCHES REQUIRED.

EE SLIPPED AT ENTRANCE TO MILL, FELL & SPRAINED BACK. BEGAN LOSING TIME 5/3/01.

EE SLIPPED WHILE DISMOUNTING TRUCK, CUT LEG ON RAILING. REPORTABLE DUE TO STITCHES AND RESTRICTED WORK. BEGAN RESTRICTED WORK 4-17-01.

EMPLOYEE WAS CHANGING FILTER BAGS AT DRYER - SPRAINED SHOULDER. BEGAN RESTRICTED DUTY 3/7/01.

THE SUPERVISOR WAS WORKING ON THE CONVEYOR BELT AND HE SLIPPED AND SPRAINED HIS WRIST WHEN HE GRABBED THE HANDRAIL. EE BEGAN LOSING TIME 2-7-01.

EMPLOYEE WAS MOVING BARREL, SLIPPED AND BARREL TIPPED OVER AND HIT FOOT. FRACTURE TO BUG TOE ON RIGHT FOOT. BEGAN LOSING TIME 10-7-00.

SUPERVISOR WAS WALKING UP STAIRS, KNEE POPPED.

EMPLOYEE STATES HE SLIPPED WALKING OUT THE CHANGE HOUSE TO BEGIN HIS SHIFT. NO LOST WORK DAYS BEGAN RESTRICTED WORK 5-17.